Medium voltage potential transformer types, specs, and applications explained
Article overview
A medium voltage potential transformer steps a 1–36kV primary voltage down to a standard 120V or 110V secondary for metering and protection. This article walks through the main design types, the IEEE C57.13 and IEC 61869-3 specs engineers compare, a practical ratio and burden calculation, Canadian CSA/Measurement Canada compliance, and where each unit fits inside a modern switchgear lineup in 2026.
Table of contents
- 1. What is a medium voltage potential transformer
- 2. Types of medium voltage potential transformers
- 3. Key specifications and standards
- 4. Sizing: ratio and burden calculation
- 5. Wiring, grounding, and protection coordination
- 6. Canadian compliance and procurement
- 7. Testing and commissioning
- 8. Applications in substations and switchgear
What is a medium voltage potential transformer
A medium voltage potential transformer is an instrument transformer that reduces 1–36kV system voltage to 120V or 110V so meters, relays, and control panels can measure it safely. It belongs to the same family as the instrument transformer group, which also includes the current transformer used for amperage sensing. Why does this distinction matter to a procurement team? Because specifying the wrong class or ratio can fail a Measurement Canada audit months after installation.
Engineers sometimes call it an MV voltage transformer, a PT, or simply a VT — these are the same device, just named differently across IEEE and IEC documentation. Real-world commissioning reports we've reviewed show that confusion over naming, not design, causes most early-stage spec errors.
What is a medium voltage potential transformer used for?
It isolates revenue meters and protective relays from dangerous primary voltage while reproducing an accurate, scaled-down waveform. Utilities, industrial substations, and switchgear manufacturers all rely on it for billing accuracy and fault detection.
Is a potential transformer the same as a voltage transformer?
Yes. Industry practice in North America favors "potential transformer" or PT, while IEC documentation and most international suppliers use "voltage transformer" or VT. There is no functional difference — it's a naming convention, not two separate products, and treating them as different device categories is a common misconception we still see in RFQs.
Types of medium voltage potential transformers
The two dominant designs are electromagnetic and capacitive, and the choice usually comes down to voltage class and budget rather than preference.
Electromagnetic vs capacitive voltage transformers
An electromagnetic voltage transformer uses a wound iron core, much like a miniature power transformer, and dominates the 5–36kV range because it's compact and highly accurate. A capacitive voltage transformer (CVT) uses a capacitor divider stack and becomes more economical above roughly 69kV — it's less common at true medium voltage but still appears in some utility interconnection points. In practical terms, if your project sits inside 5–34.5kV, an electromagnetic voltage transformer is almost always the right call; CVTs earn their keep at higher transmission voltages.
Dry type vs oil filled, indoor vs outdoor potential transformers
Dry type potential transformer units use epoxy resin encapsulation and suit indoor switchgear, panel-mount metering, and compact substations where fire codes restrict mineral oil. Oil filled potential transformer designs rely on insulating oil for cooling and dielectric strength, and they remain common in outdoor potential transformer installations at utility yards because the oil also helps dissipate heat in direct sun. A hydrophobic epoxy outdoor variant has become popular in 2026 projects across colder Canadian climates, since it resists tracking from ice and salt spray better than older resin formulations.
Both single phase potential transformer and three phase potential transformer configurations exist. North American utility practice generally favors single-unit designs wired in open-delta or wye groups rather than one integrated three-phase tank, mainly for easier field replacement.

Key specifications and standards
Two standards families govern almost every medium voltage potential transformer sold in North America: IEEE C57.13 and IEC 61869-3. Picking the wrong one for your utility's acceptance criteria is one of the most common — and expensive — ordering mistakes.
IEEE C57.13 vs IEC 61869-3: how do the standards differ?
IEEE C57.13 potential transformer units are rated using Basic Impulse Level (BIL), thermal burden ratings in VA, and accuracy classes such as 0.3, 0.6, and 1.2. IEC 61869-3 instead expresses accuracy as classes like 0.2, 0.5, and 1.0, with different burden and temperature-rise test methods. A protection class voltage transformer under IEEE rules is tested for accuracy at 5% and 100% of rated voltage during fault conditions, while IEC testing uses different reference points — this is why a unit certified under one scheme can't simply be swapped in under the other without re-verification.
| Attribute | IEEE C57.13 | IEC 61869-3 |
|---|---|---|
| Accuracy classes | 0.3, 0.6, 1.2 | 0.2, 0.5, 1.0 |
| BIL reference | kV crest, ANSI table | kV peak, IEC table |
| Burden rating | VA at rated secondary | VA at rated voltage factor |
| Typical market | Canada, United States | Europe, Asia-Pacific |
Understanding accuracy class and transformer ratio
Transformer accuracy class defines the maximum allowable error at specific burden and voltage points — a 0.3 class metering potential transformer is tight enough for revenue billing, while a 1.2 class unit might only suit indicating instruments. Voltage transformer ratio is simply primary voltage divided by secondary voltage, commonly expressed as 14400:120 or similar. Get the ratio wrong and every downstream meter reading is wrong by the same proportion — it's a quiet error that can go unnoticed for months.
Industry consensus among instrument transformer specialists holds that accuracy class selection matters as much as ratio selection, because an undersized burden can silently push a nominally 0.3 class unit into visible metering error under real field conditions.
Sizing: ratio and burden calculation
Correct sizing starts with the primary system voltage and the meter's rated input, then works backward to confirm burden capacity.
How do you calculate potential transformer ratio?
The ratio is derived from line-to-line primary voltage and the standard 120V secondary target. Here's the practical sequence we use when reviewing a customer's single-line diagram:
- Confirm nominal system voltage (e.g., 13.8kV) and whether it's line-to-line or line-to-neutral.
- Divide by the standard secondary (120V or 110V) to get the nominal ratio — 13800/120 rounds to a 115:1 class ratio.
- Select the closest standard catalog ratio; custom ratios add cost and lead time.
- Verify the accuracy class matches the connected meter's required precision.
- Calculate total connected burden in VA, including cable length losses.
- Compare calculated burden against the rated burden at the chosen accuracy class, leaving margin for future load additions.
How much burden (VA) does your PT need?
Add up the VA draw of every meter, relay, and indicating instrument on the secondary circuit, then add roughly 10–15% for long secondary cable runs — resistance in a 50-metre run isn't trivial at 120V. If total burden exceeds the rated VA at your required accuracy class, the error creeps beyond spec even though the nameplate ratio is correct. We've seen commissioning teams catch this only after a failed metering audit, which is avoidable with a five-minute burden worksheet before ordering.
Wiring, grounding, and protection coordination
Wiring configuration determines what the system can actually measure — not every arrangement detects a ground fault.
Open-delta vs wye connections: which one do you need?
An open-delta connection uses two single phase potential transformer units to measure three-phase voltage economically, but it cannot reliably detect zero-sequence (ground fault) voltage. A full wye connection with three units, each referenced to ground, supports both metering and ground-fault protection, which many Canadian utility specs now require for feeder protection relaying. If your project only needs revenue metering on a balanced system, open-delta is often acceptable and considerably cheaper.
Fusing, grounding, and ferroresonance risk
Primary-side protection typically uses an E-rated potential transformer fuse sized to the transformer's thermal and inrush characteristics — undersized fuses nuisance-trip, oversized fuses fail to protect the winding during an internal fault. Secondary circuits should be grounded at a single point only, and polarity must be verified before energizing, since reversed polarity corrupts both metering and relay directional logic. Ferroresonance — a resonant interaction between the PT's magnetizing inductance and system capacitance — is a known risk on ungrounded or resonant-grounded systems, and it can produce damaging overvoltage. Properly rated damping resistors or grounding practices mitigate this, though no configuration eliminates the risk entirely; that's a limitation worth disclosing to clients rather than glossing over.
Canadian compliance and procurement
Buying a medium voltage potential transformer for use in Canada involves more than matching electrical specs — it requires navigating Measurement Canada's approval system.
CSA approval and Measurement Canada requirements
A CSA approved voltage transformer carries certification confirming it meets Canadian electrical safety requirements, but revenue metering applications additionally require Measurement Canada notice of approval, typically referenced by an AE-xxxx approval number such as the AE-0431 series used for certain instrument transformer families. Provincial utilities generally will not accept a unit onto a billing meter point without both CSA listing and a valid Measurement Canada approval number on file. According to NRCan, Canadian electricity demand is projected to roughly double before 2050, with roughly $115 billion CAD in planned electrification investment — a trend already tightening lead times for approved substation potential transformer stock.
Pricing, lead times, and sourcing in Canada
Standard catalog ratios in CSA approved stock are often available from Canadian distributors within days, while custom ratio or accuracy-class combinations commonly run four to five weeks. Reed Intelligence estimated the Canadian instrument transformer market at roughly $714 million USD in 2025, growing toward $1.112 billion USD by 2034 at about 5.08% CAGR — a pace that has pushed some manufacturers' quoted lead times for non-stock medium voltage potential transformer units past six weeks in 2026.
| Configuration | Typical CAD price range | Typical lead time |
|---|---|---|
| Standard 5–15kV dry type, stock ratio | $350–$900 | In stock to 2 weeks |
| 25–34.5kV outdoor, stock ratio | $900–$1,800 | 2–4 weeks |
| Custom ratio or 0.3 class metering unit | $1,200–$2,500 | 4–5 weeks |
| CVT or specialty high voltage potential transformer | $2,000+ | 6+ weeks |
Prices above are general CAD estimates for budgeting purposes and vary by manufacturer, accuracy class, and current market conditions — always request a formal quote before finalizing a project budget.
Testing and commissioning
A unit that passes factory testing still needs field verification before it goes into service.
Ratio and polarity testing
Ratio testing applies a known primary voltage and confirms the secondary output matches the nameplate ratio within tolerance. Polarity testing confirms that H1 and X1 terminals maintain correct phase relationship — get this wrong and directional relays misread power flow direction, which can cause a protection scheme to fail exactly when it's needed most.
Insulation and partial discharge testing
Insulation resistance (megger) testing and partial discharge (PD) testing confirm the dielectric hasn't degraded during shipping or storage. A commissioning checklist should also include visual inspection for oil leaks on oil filled potential transformer units, torque verification on terminal connections, and a final secondary continuity check before the breaker closes. Skipping PD testing on a new outdoor potential transformer is a shortcut some crews take under schedule pressure — it's not a shortcut we'd recommend for a protection-class unit.
Applications in substations and switchgear
Where does a medium voltage potential transformer physically live? Almost always inside or adjacent to the switchgear lineup it serves.
Switchgear and substation metering
Inside metal-clad or metal-enclosed switchgear, a switchgear voltage transformer typically mounts on a roll-out truck or fixed compartment, feeding both the utility revenue meter and the local SCADA system. A substation potential transformer serving a distribution feeder often pairs with a current transformer on the same bay to provide complete power and energy measurement for billing.
Protection relaying applications
Protective relays use PT secondary voltage for distance protection, synchronism checking, and under/over-voltage tripping. A potential transformer manufacturer in Canada serving this market typically stocks both metering-class and protection-class windings on the same core, letting one unit serve both functions — a practical cost saving many smaller substations rely on.
Choosing between these applications isn't really a technical debate so much as a matching exercise — like fitting the right key to a specific lock, the transformer has to match the exact voltage, accuracy, and standard your downstream equipment expects.
常见问题解答
Q: What voltage range counts as medium voltage for a potential transformer?
A: Generally 1kV to 36kV, covering most distribution feeders, switchgear lineups, and small industrial substations in Canada.
Q: Can a medium voltage potential transformer secondary be operated open-circuit?
A: Yes, unlike a current transformer, a PT secondary can be left open safely; it's the current transformer that must never be opened under load.
Q: Do I need Measurement Canada approval for every PT installation?
A: Only for revenue billing meter points; internal process or protection-only applications typically need CSA approval but not Measurement Canada notice.
Q: What's the difference between metering class and protection class accuracy?
A: Metering class prioritizes accuracy near normal voltage; protection class must stay accurate through fault conditions up to several times rated voltage.
Q: How long do custom-ratio potential transformers take to arrive in Canada?
A: Typically four to five weeks for custom ratios in 2026, longer for specialty high voltage potential transformer designs during peak demand periods.
A medium voltage potential transformer looks simple on a nameplate, but the ratio, accuracy class, standard, and wiring configuration all have to align with the downstream meter, relay, and local approval regime before it earns its place on a feeder. Electromagnetic designs still dominate the 5–36kV range, dry type and oil filled options each suit different installation environments, and Canadian projects carry the added step of CSA and Measurement Canada verification that competitors' guides routinely skip. Engineers who run the ratio and burden numbers before ordering — rather than after a failed audit — consistently report smoother commissioning and fewer change orders.
You may be interested in
Inquire Now
Notice: Please leave your contact information, our professionals will contact you as soon as possible!
企业文化
以科技传承植物智慧,以责任守护健康未来
企业使命
食品更安全,生活更健康
今汉药业始终关注食品安全、天然健康与绿色可持续发展,致力于以植物功能成分和天然解决方案服务食品、营养健康、日化美妆、动物营养及宠物健康等领域,为客户创造更安全、更稳定、更具价值的产品选择。
企业愿景
汇今朝科技,扬汉方精粹
今汉药业坚持以现代科学技术挖掘植物资源价值,推动传统植物智慧与现代研发、绿色制造和产业应用深度融合,让来自东方的植物功能成分走向更广阔的全球市场。
企业发展方向
天然创新健康解决方案
围绕迷迭香、葫芦巴、桑叶等核心植物平台,今汉药业持续推进植物活性成分研究、提取纯化工艺升级和应用场景开发,为食品、营养健康、日化美妆、动物营养和宠物健康行业提供安全、高效、可持续的天然健康解决方案。
企业核心价值观
企业使命
食品更安全,生活更健康
今汉药业始终关注食品安全、天然健康与绿色可持续发展,致力于以植物功能成分和天然解决方案服务食品、营养健康、日化美妆、动物营养及宠物健康等领域,为客户创造更安全、更稳定、更具价值的产品选择。
企业愿景
汇今朝科技,扬汉方精粹
今汉药业坚持以现代科学技术挖掘植物资源价值,推动传统植物智慧与现代研发、绿色制造和产业应用深度融合,让来自东方的植物功能成分走向更广阔的全球市场。
企业发展方向
天然创新健康解决方案
围绕迷迭香、葫芦巴、桑叶等核心植物平台,今汉药业持续推进植物活性成分研究、提取纯化工艺升级和应用场景开发,为食品、营养健康、日化美妆、动物营养和宠物健康行业提供安全、高效、可持续的天然健康解决方案。
企业发展方向
天然创新健康解决方案
围绕迷迭香、葫芦巴、桑叶等核心植物平台,今汉药业持续推进植物活性成分研究、提取纯化工艺升级和应用场景开发,为食品、营养健康、日化美妆、动物营养和宠物健康行业提供安全、高效、可持续的天然健康解决方案。