Indoor current transformer ratio explained: 100/5A, 200/5A, and more
Article overview
This guide breaks down indoor current transformer ratios — 100/5A, 200/5A, and larger — covering selection logic, U.S. and international standards, wiring rules, and verified application cases. Designed for electrical engineers and procurement teams at the specification and sourcing stage.
Table of contents
- 1. What is an indoor current transformer ratio?
- 2. How indoor and outdoor CTs fundamentally differ
- 3. Common ratio options: 100/5A, 200/5A, and beyond
- 4. How to select the right CT ratio: a step-by-step guide
- 5. Accuracy classes and standards: IEEE C57.13 vs IEC 61869-2
- 6. Wiring, polarity, and installation rules
- 7. Testing, commissioning, and maintenance
- 8. Real application cases
- 9. Frequently asked questions
What is an indoor current transformer ratio?
An indoor current transformer is a low-voltage, epoxy-resin-encapsulated instrument transformer designed for enclosed environments that steps down high primary currents to a standardized 1A or 5A secondary output for metering and protection circuits. The ratio — expressed as primary/secondary, such as 100/5A or 200/5A — defines exactly how much the current is scaled. A 200/5A unit, for instance, produces 5A at the secondary terminals when 200A flows through the primary conductor.
Why does the ratio matter so much? Because every downstream device — energy meters, relays, RTUs — is calibrated to a specific input range. Feed the wrong ratio into a revenue-grade energy meter and your billing data will be systematically off by a fixed multiplier. That is not a small problem in a commercial substation or industrial plant.
The ratio is not an arbitrary number, either. It emerges from the magnetic core design, the number of secondary turns, and the intended burden. Understanding that chain of cause and effect is what separates a confident specification from a costly mistake. For background on current transformer basics, the foundational electromagnetic principles are well documented in open engineering literature.
Primary-to-secondary relationship
The nominal ratio is calculated as N₂/N₁, where N₁ is primary turns and N₂ is secondary turns. For a single-pass primary (busbar or straight-through cable), N₁ = 1, so a 200/5A CT needs 40 secondary turns. Increasing primary turns — by looping the cable through the window — reduces the effective ratio, a trick used when an oversized CT is the only one in stock. A 400/5A unit with two primary turns becomes a functional 200/5A unit. This works, but introduces a small error; for revenue-grade or Class 0.2S applications it should be avoided.
Why 5A secondary is dominant in the U.S.
North American practice, governed by IEEE C57.13, standardizes on 5A secondary current. European and IEC-aligned markets often use 1A, particularly for long secondary cable runs where the lower current reduces I²R losses in the wiring. When specifying an indoor CT sensor for a U.S. switchboard, always confirm secondary rating before ordering — a 1A CT wired to a 5A meter input produces a ratio error of 500%, destroying any measurement accuracy.
How indoor and outdoor CTs fundamentally differ
The distinction between indoor and outdoor instrument transformers is not merely cosmetic. It drives insulation design, pollution withstand, enclosure rating, and long-term reliability — all factors that affect procurement decisions.
Insulation medium and pollution class
Indoor current transformers for indoor use overwhelmingly use cast epoxy resin encapsulation. The resin provides solid, uniform insulation around the toroidal or wound core, giving excellent mechanical strength and resistance to condensation. Outdoor units, by contrast, historically used oil-immersed designs with porcelain or silicone rubber housings. The oil provides superior thermal dissipation for high-voltage, high-current applications but introduces leakage risk and requires periodic oil sampling — neither of which is acceptable inside a metal-clad switchgear panel.
Pollution degree classification under IEC 60664 defines how much surface contamination an insulation system must withstand. Indoor enclosed current transformers are typically rated Pollution Degree 2 (normally only non-conductive contamination), whereas outdoor units must meet Pollution Degree 3 or 4. Creepage distance requirements drop significantly in Pollution Degree 2 environments, which is why indoor low voltage current transformers can be physically much more compact than their outdoor equivalents at the same voltage class.
IP rating, altitude, and thermal derating
A panel mount current transformer installed inside a sealed switchgear cubicle typically carries an IP20 or IP30 enclosure rating — adequate for the protected environment. Outdoor units require IP54 or higher. Altitude matters too: at elevations above 3,300 ft (1,000 m), air density decreases, reducing dielectric strength and convective cooling. IEEE C57.13 and IEC 61869-2 both require derating the continuous thermal current rating by approximately 1% per 330 ft (100 m) above 3,300 ft. For high-altitude installations in Denver or Albuquerque, this is a real engineering consideration, not a footnote.

Common ratio options: 100/5A, 200/5A, and beyond
The range of standardized ratios for indoor ring core transformers and wound-type units covers a wide span of primary currents, all sharing the same 5A secondary (in U.S.-market products). The table below summarizes the most common ratios, their typical applications, and the standard window bore sizes available in the market as of 2026.
| CT ratio | Typical primary current (A) | Common application | Typical window bore (mm) | Accuracy class (IEC) |
|---|---|---|---|---|
| 50/5A | Up to 50 | Small panel boards, lighting circuits | 24–30 | 0.5, 1.0 |
| 100/5A | Up to 100 | Commercial sub-metering, MCC feeders | 30–40 | 0.2S, 0.5, 5P |
| 150/5A | Up to 150 | HVAC equipment feeders | 30–40 | 0.5, 1.0 |
| 200/5A | Up to 200 | Distribution panels, medium industrial loads | 40–50 | 0.2S, 0.5, 5P, 10P |
| 400/5A | Up to 400 | Main service entrance, bus sections | 50–60 | 0.2S, 0.5, 5P |
| 600/5A | Up to 600 | Large commercial/industrial service | 60–80 | 0.5, 5P, 10P |
| 1200/5A | Up to 1200 | Switchgear, busbar current transformer applications | 80–120 | 0.2S, 0.5, 5P |
| 2000/5A | Up to 2000 | Utility metering, large industrial busbars | 100–150 | 0.2S, 0.5 |
Notice how window bore grows with ratio. This is a physical inevitability: larger primary conductors carry higher currents and demand a larger opening. When retrofitting an older cubicle, always measure the available conductor diameter before ordering an indoor split core CT — a unit with a 40 mm bore will not accept a 60 mm cable without core splitting.
The 80% loading rule
A well-known field principle — sometimes called the 80% rule — states that the CT primary rating should be chosen so that the expected continuous load current does not exceed 80% of the CT's rated primary current. So for a feeder with a maximum demand of 160A, a 200/5A unit is the correct choice, not a 150/5A. This headroom prevents saturation under transient overloads and keeps ratio error within the accuracy class limits across the operating range.
When non-standard ratios are needed
Standard ratios cover most applications, but what about a 175A transformer feeder? Some manufacturers offer intermediate ratios — 175/5A, 250/5A, 300/5A — as catalog items. Alternatively, a 200/5A unit can be ordered with a dual-ratio tap (100-200/5A), allowing field adjustment. For very unusual currents, custom wound units are available, though lead time typically extends to 8–12 weeks and minimum order quantities apply.
How to select the right CT ratio: a step-by-step guide
Ratio selection is a systematic process, not a guess. The following procedure applies to any metering current transformer or protection current transformer installed in a low-voltage or medium-voltage indoor panel.
- Determine maximum continuous primary current. Use the feeder's overcurrent protective device rating or the connected load's full-load ampere rating — whichever is larger. Add a 25% margin for motor starting or demand growth.
- Apply the 80% rule. Divide the maximum current by 0.8 to get the minimum CT primary rating. Round up to the next standard ratio.
- Confirm secondary rating. For U.S. applications, 5A secondary is standard. For international or IEC-aligned projects, verify whether 1A is required.
- Calculate secondary burden. Total burden (VA) = sum of all connected meter VA + lead wire resistance loss (I²R, where I = 5A and R = cable length × resistance per unit length × 2). The total burden must not exceed the CT's rated VA burden.
- Select accuracy class. Revenue metering requires 0.2S or 0.5 class. General power monitoring accepts Class 1. Overcurrent and earth-fault protection uses 5P or 10P class.
- Verify short-time current rating. The CT must withstand the installation's available fault current for the rated short-time duration (typically 1 second). Check both thermal short-time current (Ith) and dynamic peak current (Idyn) against the switchgear's prospective fault level.
- Check physical fit. Confirm window bore accommodates the primary conductor, and that the CT body fits within the panel mounting space.
Secondary burden and lead wire calculation example
Consider a 200/5A energy monitoring current transformer serving a revenue meter with a 5 VA burden, connected by 2.5 mm² copper cable over 15 meters (one-way). Lead resistance = 15 m × 2 × (1/56 Ω·mm²/m per mm²) ÷ 2.5 mm² ≈ 0.21 Ω. At 5A secondary, lead burden = 5² × 0.21 = 5.25 VA. Total burden = 5 + 5.25 = 10.25 VA. A 10 VA rated CT is marginally insufficient; specify a 15 VA unit to maintain accuracy class compliance.
ALF (accuracy limit factor) and protection CTs
For protection applications, the accuracy limit factor (ALF) defines how many times rated current the CT can reproduce accurately before core saturation distorts the output. A 5P20 CT maintains 5% composite error up to 20× rated current. If your overcurrent relay requires accurate operation at 15× rated current, a 5P20 is sufficient; a 5P10 is not. Always cross-reference ALF against the relay's operating characteristic minimum pickup current in multiples of rated current.
Accuracy classes and standards: IEEE C57.13 vs IEC 61869-2
North American engineers specify indoor instrument transformers primarily under IEEE C57.13, while IEC 61869-2 governs products for most of the rest of the world — and increasingly appears in U.S. projects with international equipment suppliers. Understanding both frameworks prevents costly specification mismatches.
"Revenue-grade accuracy requires not just a low ratio error at rated current, but maintained accuracy at light loads — which is why the 'S' suffix in Class 0.2S and Class 0.5S specifies extended accuracy down to 1% of rated current, critical for smart grid billing applications." — IEC 61869-2:2012, Clause 5.6 accuracy requirements summary
IEEE C57.13 metering and relaying classes
IEEE C57.13 defines metering accuracy classes as 0.3 and 0.6 (expressed as percentage ratio error at rated current). For relaying, the standard uses a letter-number system: C100, C200, C400, and C800. The letter C (or T for wound-type) indicates the method of classification, and the number represents the secondary terminal voltage the CT can deliver at 20× rated secondary current without exceeding a 10% ratio error. A C200 relay-class CT, for example, sustains 200V at the secondary under maximum fault current — directly sizing the CT for the burden and fault level of the protection circuit.
IEC 61869-2 accuracy classes and 60 Hz vs. 50 Hz
IEC classifies metering CTs as 0.1, 0.2, 0.2S, 0.5, 0.5S, 1, and 3; protection CTs as 5P, 10P, and PR/PX classes. The 'S' suffix classes (0.2S, 0.5S) maintain accuracy from 1% to 120% of rated current, essential for smart metering at low load. One critical cross-standard issue: IEC cores are designed for 50 Hz. At 60 Hz (U.S. standard), core losses decrease slightly, generally improving accuracy slightly, but the datasheet VA burden rating is defined at 50 Hz. At 60 Hz, the burden a CT can support is marginally higher — typically by a factor of 60/50 = 1.2 — but manufacturers should be consulted before relying on this factor for revenue applications. UL and CSA certification, combined with NEC Article 110 instrument transformer installation requirements, govern the final compliance verification for U.S. installations.
Wiring, polarity, and installation rules
Getting the ratio right on paper means nothing if the CT is wired incorrectly in the field. Polarity errors introduce phase angle errors that corrupt power factor and energy calculations. Open-circuiting the secondary is a safety hazard that every technician must understand before touching a live panel.
P1/P2 and S1/S2 terminal conventions
By convention, current entering the P1 primary terminal exits S1 on the secondary simultaneously — this is the additive polarity dot convention. For a switchgear current transformer wired to a watt-hour meter, P1 faces the source side and S1 connects to the meter's current input terminal. Reversing P1/P2 swaps the phase relationship by 180°, causing the meter to record negative power or accumulate reverse energy — a common commissioning error that is easy to make and expensive to discover after a billing dispute.
The open-circuit prohibition and secondary grounding
Never open the secondary circuit of an energized CT. With the secondary open, all primary MMF drives the core into saturation, inducing dangerous high-voltage spikes at the secondary terminals — voltages that can reach several kilovolts and are lethal. This is not a theoretical warning. Test terminal blocks with shorting facilities (a short-circuit device) must be installed on every CT secondary circuit to allow meter replacement without de-energizing the primary. Additionally, one point on the CT secondary circuit must be solidly grounded (NEC 250.170) to limit the voltage-to-ground on secondary wiring under fault conditions.
When using an indoor split core CT for retrofit installations, verify that the split core halves lock together securely and that the gap is minimized — even a 0.1 mm air gap in a toroidal core increases magnetizing current and degrades accuracy, sometimes by a full accuracy class.
Testing, commissioning, and maintenance
A CT that leaves the factory within spec can still fail in service if commissioning tests are skipped or maintenance intervals are ignored. The following tests cover both factory acceptance and site verification.
Routine and type test checklist
IEC 61869-2 distinguishes routine tests (performed on every unit) from type tests (performed on a design representative). Routine tests include: ratio verification, polarity check, secondary winding resistance measurement, and power-frequency withstand (applied and induced voltage). Type tests add: accuracy class verification over the full current range, temperature rise test, short-time current test, and partial discharge measurement. For revenue grade current transformer procurement, request the type test report and verify that the tested unit's core material and winding construction match the production batch.
Excitation (knee-point) curve and site verification
The excitation or V-I characteristic test reveals the knee-point voltage — the inflection point on the magnetization curve above which a small increase in secondary voltage causes a large increase in magnetizing current. For protection CTs, the knee-point voltage must exceed the product of ALF × rated secondary current × (CT secondary resistance + connected burden resistance). On site, a simple ratio check with a portable CT analyzer verifies ratio and phase angle against the nameplate, typically taking under five minutes per unit. Maintenance intervals of 3–5 years are standard for indoor enclosed current transformers in clean panel environments, extending to annual checks in high-humidity or high-vibration installations.
Real application cases: switchgear, ring main units, and retrofits
Theory becomes concrete when applied to actual installation scenarios. The following cases illustrate how ratio selection, physical sizing, and standard compliance interact in practice.
Case 1 — Medium-voltage metal-clad switchgear (15 kV, 1200A bus)
A 15 kV indoor switchgear lineup requires metering and protection CTs on each feeder breaker. Feeder load is 800A continuous. Applying the 80% rule: 800 ÷ 0.8 = 1000A minimum primary rating. The engineer specifies 1200/5A units. Accuracy class: 0.2S for revenue metering, 5P20 for the overcurrent relay cores (dual-ratio core in one CT housing). Short-time current rating: 40 kA for 1 second (matching the switchgear's interrupting rating). Physical fit: 80 mm window bore accommodates the 1200A copper busbar. The busbar current transformer is factory-fitted to the switchgear draw-out assembly before shipment.
Case 2 — Ring main unit (RMU) for commercial building
A compact 12 kV ring main unit serves a 500 kVA transformer (rated primary current ≈ 24A at 12 kV). Here the primary current is low, but the application requires protection-grade accuracy for feeder overcurrent and earth-fault relays. The engineer selects 50/5A, Class 5P20 units — small window bore (30 mm), low VA burden to match the compact relay panel inside the RMU. This is a case where choosing a larger ratio like 100/5A would be technically permissible but would reduce the relay's sensitivity at minimum fault current.
Case 3 — Legacy panel retrofit with space constraints
An older 400A distribution board needs energy monitoring added for a building energy management system. The existing cable is 185 mm² aluminum, with a measured outer diameter of 42 mm. A solid-core 400/5A unit with a 50 mm bore would require removing the cable — impractical in a live building. The solution: an indoor split core CT, 400/5A, Class 0.5, with a 60 mm split opening. Accuracy is marginally lower than a solid-core equivalent due to the core joint, but Class 0.5 is fully adequate for energy monitoring (not revenue billing). Installation time: under 30 minutes per phase with the feeder energized, using the shorting block on the test terminal.
Frequently asked questions
Q: What is the difference between an indoor and outdoor current transformer?
A: Indoor current transformers use cast epoxy resin insulation rated for Pollution Degree 2 environments and typically carry IP20–IP30 enclosure ratings. Outdoor units use oil-immersed or silicone-rubber insulation designed for Pollution Degree 3–4, with IP54 or higher ratings. Indoor units cannot be used outdoors; the lower creepage distance and lack of weatherproofing will cause premature insulation failure.
Q: How do I apply the 80% rule when selecting a CT ratio?
A: Determine the maximum continuous primary current, then divide by 0.8 to find the minimum rated primary current. Round up to the next standard ratio. For a 160A load: 160 ÷ 0.8 = 200A — select a 200/5A CT. This headroom prevents core saturation during transient overloads and maintains accuracy class compliance.
Q: Can a 200/5A CT be used as a 100/5A by looping the cable twice?
A: Yes, passing the primary conductor through the CT window twice doubles the effective turns ratio, converting a 200/5A unit to 100/5A. This is acceptable for general monitoring but introduces a small additional error due to uneven conductor positioning. For revenue metering or Class 0.2S accuracy, use a correctly rated unit instead.
Q: What happens if the CT secondary circuit is left open while the primary is energized?
A: An open secondary forces the entire primary MMF into the magnetic core, saturating it and inducing dangerously high voltages at the secondary terminals — potentially several kilovolts. This is a serious personnel safety hazard and can permanently damage the CT insulation. Always short the secondary terminals before disconnecting any instrument or relay in the secondary circuit.
Q: What is the difference between IEEE C57.13 relay class C200 and IEC Class 5P20?
A: IEEE C200 defines the CT by its secondary terminal voltage capability (200V at 20× rated current with ≤10% ratio error). IEC 5P20 defines it by composite error (≤5%) at 20× rated current with a specified burden. Both describe protection-grade performance, but the metrics are not directly interchangeable; always verify the actual knee-point voltage and burden rating against your relay's requirements.
Conclusion
Selecting the correct indoor current transformer ratio is a disciplined engineering process — not a catalog lookup. From the fundamental 100/5A and 200/5A configurations to high-current 1200/5A and 2000/5A units for switchgear busbars, every ratio choice must be backed by load analysis, burden calculation, accuracy class verification, and physical fit confirmation. The difference between IEEE C57.13 and IEC 61869-2 matters when sourcing internationally; the 80% loading rule and the absolute prohibition on open secondary circuits are field realities that protect both equipment and personnel.
When evaluating suppliers for indoor instrument transformer procurement, look beyond the nameplate ratio. Request type test certificates, verify the core material grade, confirm short-time current ratings against your fault study, and ensure UL or CSA listing for U.S. installations. A well-specified indoor CT sensor installed correctly will deliver accurate, reliable data for the 20–30 year lifespan of the switchgear it serves. That long-term reliability — not the unit price — is the true measure of value in this category.
You may be interested in
Inquire Now
Notice: Please leave your contact information, our professionals will contact you as soon as possible!
企业文化
以科技传承植物智慧,以责任守护健康未来
企业使命
食品更安全,生活更健康
今汉药业始终关注食品安全、天然健康与绿色可持续发展,致力于以植物功能成分和天然解决方案服务食品、营养健康、日化美妆、动物营养及宠物健康等领域,为客户创造更安全、更稳定、更具价值的产品选择。
企业愿景
汇今朝科技,扬汉方精粹
今汉药业坚持以现代科学技术挖掘植物资源价值,推动传统植物智慧与现代研发、绿色制造和产业应用深度融合,让来自东方的植物功能成分走向更广阔的全球市场。
企业发展方向
天然创新健康解决方案
围绕迷迭香、葫芦巴、桑叶等核心植物平台,今汉药业持续推进植物活性成分研究、提取纯化工艺升级和应用场景开发,为食品、营养健康、日化美妆、动物营养和宠物健康行业提供安全、高效、可持续的天然健康解决方案。
企业核心价值观
企业使命
食品更安全,生活更健康
今汉药业始终关注食品安全、天然健康与绿色可持续发展,致力于以植物功能成分和天然解决方案服务食品、营养健康、日化美妆、动物营养及宠物健康等领域,为客户创造更安全、更稳定、更具价值的产品选择。
企业愿景
汇今朝科技,扬汉方精粹
今汉药业坚持以现代科学技术挖掘植物资源价值,推动传统植物智慧与现代研发、绿色制造和产业应用深度融合,让来自东方的植物功能成分走向更广阔的全球市场。
企业发展方向
天然创新健康解决方案
围绕迷迭香、葫芦巴、桑叶等核心植物平台,今汉药业持续推进植物活性成分研究、提取纯化工艺升级和应用场景开发,为食品、营养健康、日化美妆、动物营养和宠物健康行业提供安全、高效、可持续的天然健康解决方案。
企业发展方向
天然创新健康解决方案
围绕迷迭香、葫芦巴、桑叶等核心植物平台,今汉药业持续推进植物活性成分研究、提取纯化工艺升级和应用场景开发,为食品、营养健康、日化美妆、动物营养和宠物健康行业提供安全、高效、可持续的天然健康解决方案。