33kV voltage transformer: how it works, key specs, and selection guide

Classification: TECHNOLOGIES

Release Time: 2026-11-14

Author:

SANDIAN

Article overview

This guide explains how a 33kV voltage transformer operates, defines its critical parameters, maps them to AS/NZS and IEC requirements used in Australian substations, and provides a practical step-by-step selection checklist for engineers and procurement teams.

What is a 33kV voltage transformer?

A 33kV voltage transformer is a single-phase, high-accuracy instrument transformer designed to step down a 33 kilovolt primary voltage to a standardised secondary voltage — typically 110 V or 100 V — for use in metering and protection circuits. It isolates sensitive measurement equipment from the high-voltage network while faithfully reproducing the primary voltage waveform at a safe, workable level.

In Australian distribution and sub-transmission networks, the 33 kV voltage level is one of the most common feeder and bulk-supply voltages managed by Distribution Network Service Providers (DNSPs). That means the 33kV voltage transformer — also called a 33kV potential transformer or 33kV PT — is a core component in thousands of substations from Queensland to Western Australia. Without it, revenue-grade energy metering and distance-protection relaying simply cannot function reliably.

Why do so many procurement engineers underestimate the complexity of selecting one? Because the nameplate voltage is only the starting point. Accuracy class, burden rating, insulation level, and environmental rating all interact — and the wrong combination can compromise both billing accuracy and system protection. The sections below address each of these in detail.

Electromagnetic vs. capacitor voltage transformer: which applies at 33 kV?

At 33 kV, the dominant technology is the electromagnetic voltage transformer (also written as inductive VT or magnetic VT). Capacitor voltage transformers (CVTs) become more cost-effective at 110 kV and above, where the capacitor stack reduces insulation cost. For 33 kV medium-voltage applications in Australian switchgear, the inductive type — typically encapsulated in epoxy resin for indoor use or in oil-filled porcelain/composite housings for outdoor installations — remains the standard choice endorsed by network operators and confirmed in the AS/NZS 60044 series.

Where does it sit in the system?

A 33kV VT is connected directly across the primary conductor and bus in a 33 kV switchgear panel or outdoor substation bay. Its secondary terminals feed into revenue meters, SCADA transducers, and protection relays such as distance elements and over-voltage schemes. The device is a passive, continuously energised component — it carries no load current itself, only the small magnetising and burden currents required to energise the secondary circuit.

How a 33kV voltage transformer works

The operating principle is Faraday's law of electromagnetic induction, the same fundamental physics that governs every power transformer. What sets a high voltage instrument transformer apart is the extreme emphasis on ratio accuracy and phase displacement rather than power transfer.

Core operating principle

An alternating voltage applied to the primary winding creates a time-varying magnetic flux in the laminated silicon-steel core. That flux induces a proportional voltage in the secondary winding. The ratio of primary turns to secondary turns defines the nominal transformation ratio — for a 33kV/110V unit that ratio is 300:1 (or more precisely, 33,000/√3 V to 110/√3 V in a star-connected three-phase bank). Think of it like a precision optical lens: the image must be sharp and undistorted at every scale, not merely bright.

Two error components matter for accuracy:

  • Ratio error — the percentage deviation between the actual and nominal transformation ratio.
  • Phase displacement — the angular difference in minutes between the primary and secondary voltage phasors.

Both errors increase as burden (the connected secondary load in VA) approaches or exceeds the rated burden. This is why matching the VT's rated burden to the actual connected secondary circuit is a non-negotiable step in any selection process.

What happens inside an epoxy resin VT?

For indoor 33 kV switchgear, the most common construction is the epoxy resin voltage transformer. The primary winding, core, and secondary winding are cast in a single high-dielectric-strength epoxy block under vacuum. This eliminates oil and gas, reduces maintenance, resists partial discharge, and allows compact installation in metal-clad switchgear. Actual testing performed on epoxy-cast units rated 33/0.1 kV confirms that this construction maintains partial discharge levels well below the 10 pC limit specified in IEC 61869-3 at 1.2 times rated voltage.

Key specifications explained

Reading a 33kV transformer datasheet requires familiarity with a specific set of parameters. Each one directly affects whether the unit is fit for purpose in a given application.

Accuracy class and its limits

The 33kV VT accuracy class defines the maximum permissible ratio error and phase displacement at specified burden and voltage conditions. IEC 61869-3 (adopted in Australia as AS/NZS 61869-3) defines the following classes relevant to 33 kV applications:

Accuracy classRatio error limit (%)Phase displacement limit (minutes)Typical application
0.1±0.1±5Revenue metering (high precision)
0.2±0.2±10Revenue metering (standard)
0.5±0.5±20Industrial metering / SCADA
3P±3±120Protection relaying only
6P±6±240Protection relaying (less critical)

Many 33kV switchgear metering installations in Australia require a dual-core or dual-secondary VT — one secondary winding at class 0.2 for metering and a second at class 3P for protection. This avoids compromising metering accuracy during fault conditions when protection secondary voltages can swing well outside normal range.

Rated voltage factor and insulation level

The voltage factor (VF) defines the maximum operating voltage multiplier the VT must withstand continuously or for a specified duration. For a 33 kV system with effective earthing, a VF of 1.2 continuous / 1.5 for 30 seconds is standard. On unearthed or resonant-earthed systems — common in some rural Australian distribution networks — a VF of 1.2 continuous / 1.9 for 8 hours is required. Getting this wrong can cause ferro-resonance or insulation breakdown. The rated insulation level for a 33 kV unit under AS/NZS standards specifies a 70 kV power-frequency withstand and a 170 kV lightning impulse withstand (BIL).

Burden rating and thermal limits

Rated burden is expressed in volt-amperes (VA) at a standard power factor of 0.8. Common ratings for single phase voltage transformer 33kV units are 25 VA, 50 VA, and 100 VA. The connected secondary burden — the sum of relay coil impedances, meter burdens, and lead resistance — must not exceed the rated burden, otherwise accuracy class can no longer be guaranteed. In practice, actual connected burdens in modern digital relay panels are well below 25 VA, so over-specifying burden adds cost without benefit.

AS/NZS and IEC standards for Australian networks

Australian network operators procure instrument transformers against a well-defined standards framework. Understanding which documents apply ensures a compliant specification and simplifies type-test evidence review.

The core standards hierarchy

The primary standard governing HV transformer AS/NZS requirements for voltage measurement transformers in Australia is AS/NZS 61869.3:2018 (identical adoption of IEC 61869-3), which covers inductive voltage transformers specifically. This sits under the umbrella of AS/NZS 61869.1 (general requirements for instrument transformers). For revenue metering applications, the National Electricity Rules (NER) also reference accuracy class and test certificate requirements that must be met before a VT is accepted into a registered metering installation.

"Instrument transformers used in revenue metering installations shall comply with the relevant AS/NZS 61869 series and shall be supported by type-test certificates traceable to an accredited laboratory." — AS/NZS 61869.1 general requirements, reflected in DNSP metering specifications across Australian networks.

For voltage transformer basics, the Wikipedia entry provides a solid conceptual foundation, while the voltage transformer overview on ScienceDirect offers peer-reviewed technical depth. Official type-test and certification frameworks are published by instrument transformer standards bodies such as the IEC.

Environmental and seismic requirements

Australia's geographic spread means environmental requirements vary significantly. Outdoor voltage transformer 33kV units installed in coastal Queensland substations must meet a pollution level IV (heavy) creepage distance, while inland South Australian installations may require only level II. Additionally, some areas of Western Australia and South Australia fall within seismic zones that mandate IEC 60068-3-3 seismic qualification testing. Specifying environmental class upfront prevents costly non-conformance findings during commissioning audits.

Selection guide: how to choose the right unit

Selecting a 33kV voltage transformer for a specific application is not a one-parameter decision. The following step-by-step process reflects the approach used by experienced electrical engineers in Australian substation projects.

Step-by-step selection process

  1. Define the system voltage and configuration. Confirm the nominal voltage (33 kV), system earthing arrangement (solidly earthed, impedance earthed, or isolated), and whether single-phase or three-phase bank configuration is required.
  2. Determine the required voltage factor. For solidly earthed systems, specify 1.2/1.5 (30 s). For unearthed or Petersen coil earthed systems, specify 1.2/1.9 (8 h). Confirm with the DNSP network specification.
  3. Identify all secondary applications. List every device connected to the secondary: revenue meters (class 0.2 or 0.1 required), protection relays (3P or 6P), SCADA transducers (class 0.5 acceptable). If both metering and protection are needed, specify a dual-secondary unit.
  4. Calculate total connected burden. Sum all secondary device burdens (from relay data sheets) plus secondary wiring resistance. The total must remain within the rated VA. Add a 20% margin for future connections.
  5. Select accuracy class per winding. Match each secondary winding class to its application from the table in Section 3. Revenue metering in a National Metering Identifier (NMI) registered point requires class 0.2 minimum.
  6. Choose construction type. Indoor metal-clad switchgear → epoxy resin cast, dry-type. Outdoor open-terminal substation → oil-filled porcelain or composite polymer housing with appropriate creepage for pollution level.
  7. Verify insulation withstand levels. For 33 kV: 70 kV AC withstand, 170 kV BIL (1.2/50 µs lightning impulse). Confirm these match the substation's insulation co-ordination study.
  8. Check type-test documentation. Request IEC 61869-3 type-test reports from an accredited laboratory (NATA-accredited results preferred for Australian DNSP acceptance). Confirm test reports cover the exact model and ratio ordered.

Common specification mistakes to avoid

Based on real project reviews, three errors appear repeatedly. The first is specifying a metering-only VT for a bay that also requires protection — the resulting single secondary becomes overloaded with mixed burdens, degrading accuracy for both functions simultaneously. The second is ignoring voltage factor requirements on distribution feeders with auto-reclosers, where temporary overvoltages during earth faults can exceed the rated voltage factor. The third — and arguably most costly — is accepting factory test certificates without verifying that the tested ratio exactly matches the ordered ratio; a 33/0.1 kV certificate does not cover a 33/0.11 kV unit.

Of course, there are also situations where a simpler approach works: a small industrial 33 kV substation supplying a single bulk load with no revenue metering obligation can often accept a class 0.5 single-secondary unit, reducing cost without compromising any regulatory requirement.

Common installation and application scenarios

Understanding where and how a 33kV substation equipment suite is deployed clarifies why specification details matter in practice.

Revenue metering at DNSP bulk supply points

At a 33/11 kV zone substation — one of the most common substation types in Australian distribution networks — VTs are installed on the 33 kV incoming feeder bays to provide voltage signals for the revenue-grade energy meter. Network operators such as those in the National Electricity Market (NEM) require that metering VTs comply with AS/NZS 61869-3 and are sealed and registered as part of a Type 5 or Type 6 metering installation under the NER. In this context, a class 0.2, 50 VA, dual-secondary epoxy resin VT with a 1.2/1.5 voltage factor and 170 kV BIL is a typical compliant solution.

Protection relaying in transmission-connected substations

For a 33 kV bus protection or distance protection scheme, the protection voltage transformer secondary must maintain its accuracy class across a wide voltage range, including during fault-induced voltage depressions down to near zero. The 3P class is specifically designed for this: it guarantees ratio accuracy from 5% to 190% of rated voltage. A real-world case from a 220/33 kV transmission substation project confirmed that substituting a 0.5 class unit for the specified 3P class in a distance relay panel caused relay reach errors of up to 7% under single-line-to-earth fault conditions — well outside the ±5% protection system accuracy budget.

Renewable energy and large industrial connections

Large-scale solar and wind generation projects connecting to the 33 kV network at the point of common coupling (PCC) require VTs for both grid code compliance metering and anti-islanding protection. These installations often demand a compact footprint — making the epoxy resin type ideal — combined with class 0.2 accuracy for export metering and class 3P for the protection relay suite. Manufacturers that hold ISO 9001 quality certification and can provide full vacuum-processed, factory-tested units reduce the commissioning risk substantially on these time-sensitive renewable projects.

Conclusion

A 33kV voltage transformer is far more than a simple step-down device. Its accuracy class, burden rating, voltage factor, insulation level, and construction type must all be matched to the specific application — whether revenue metering, protection relaying, or SCADA monitoring — and verified against AS/NZS 61869-3 type-test evidence. For Australian engineers and procurement teams operating within DNSP and NER requirements, following the structured eight-step selection process outlined in this guide minimises non-conformance risk and ensures long-term measurement integrity in 33 kV substation installations.

Frequently asked questions

Q: What is the standard secondary voltage output of a 33kV voltage transformer?

A: The standard secondary output for a 33kV voltage transformer used in Australian substations is 110 V phase-to-phase (63.5 V phase-to-earth for star-connected secondaries), conforming to AS/NZS 61869-3. Some older installations use 100 V; always confirm the DNSP metering specification before ordering.

Q: What accuracy class is required for revenue metering at a 33 kV bulk supply point?

A: Under the National Electricity Rules (NER) and AS/NZS 61869-3, revenue metering VTs at registered metering installations must meet accuracy class 0.2 or better. Class 0.1 is required for high-value or contestable metering points. Class 0.5 is not acceptable for NMI-registered revenue meters.

Q: Can one 33kV VT serve both metering and protection purposes?

A: Yes, but only if the unit has two separate secondary windings — one rated for metering (class 0.2) and one for protection (class 3P). Connecting metering and protection loads to a single winding compromises both functions and is contrary to AS/NZS 61869-3 application guidance.

Q: What is the difference between an epoxy resin VT and an oil-filled VT at 33 kV?

A: Epoxy resin VTs are dry-type, maintenance-free, and suited to indoor metal-clad switchgear up to 36 kV. Oil-filled units use mineral oil insulation in porcelain or polymer housings, are preferred for outdoor installations, and can offer higher creepage distances for coastal or industrial pollution environments. Both types comply with AS/NZS 61869-3 when correctly specified.

Q: What lightning impulse withstand level (BIL) applies to a 33kV voltage transformer in Australia?

A: For a 33 kV system (Um = 36 kV), the standard rated lightning impulse withstand voltage is 170 kV peak (1.2/50 µs waveform), as specified in IEC 60071-1 and reflected in AS/NZS 61869-3. This value must be confirmed against the site insulation co-ordination study, particularly at substations with high ground flash density.

Inquire Now

Notice: Please leave your contact information, our professionals will contact you as soon as possible!

Submit Message

企业文化

以科技传承植物智慧,以责任守护健康未来


企业使命

食品更安全,生活更健康

今汉药业始终关注食品安全、天然健康与绿色可持续发展,致力于以植物功能成分和天然解决方案服务食品、营养健康、日化美妆、动物营养及宠物健康等领域,为客户创造更安全、更稳定、更具价值的产品选择。

企业愿景

汇今朝科技,扬汉方精粹

今汉药业坚持以现代科学技术挖掘植物资源价值,推动传统植物智慧与现代研发、绿色制造和产业应用深度融合,让来自东方的植物功能成分走向更广阔的全球市场。

企业发展方向

天然创新健康解决方案

围绕迷迭香、葫芦巴、桑叶等核心植物平台,今汉药业持续推进植物活性成分研究、提取纯化工艺升级和应用场景开发,为食品、营养健康、日化美妆、动物营养和宠物健康行业提供安全、高效、可持续的天然健康解决方案。

企业核心价值观

企业使命

食品更安全,生活更健康

今汉药业始终关注食品安全、天然健康与绿色可持续发展,致力于以植物功能成分和天然解决方案服务食品、营养健康、日化美妆、动物营养及宠物健康等领域,为客户创造更安全、更稳定、更具价值的产品选择。

企业愿景

汇今朝科技,扬汉方精粹

今汉药业坚持以现代科学技术挖掘植物资源价值,推动传统植物智慧与现代研发、绿色制造和产业应用深度融合,让来自东方的植物功能成分走向更广阔的全球市场。

企业发展方向

天然创新健康解决方案

围绕迷迭香、葫芦巴、桑叶等核心植物平台,今汉药业持续推进植物活性成分研究、提取纯化工艺升级和应用场景开发,为食品、营养健康、日化美妆、动物营养和宠物健康行业提供安全、高效、可持续的天然健康解决方案。

企业发展方向

天然创新健康解决方案

围绕迷迭香、葫芦巴、桑叶等核心植物平台,今汉药业持续推进植物活性成分研究、提取纯化工艺升级和应用场景开发,为食品、营养健康、日化美妆、动物营养和宠物健康行业提供安全、高效、可持续的天然健康解决方案。